BMW ICOM

BMW ICOM NEXT is the Latest Generation Diagnostic Head For BMW, for MINI, for Rolls-Royce for BMW-Model. This tool Can Replace for BMW ICOM A2 , including all function of ICOM A2. This is the best diagnostic and programming tools for BMW Serial cars. Recently, most of the customers meet problem to use BMW ICOM software , get error “Unregistered” shown as below. Message reads ” This application needs a valid key to start, please paste your serial number below. You may contact us at …… for details. The problem like the picture below: If you meet this problem, The only thing you need to do is run the “ID.reg” file so it will add some info to the registry. After this, ISTA/D should work fine! Get the file from here, unpack it and double click it. https://mega.nz/#!BIJhSYAa!v2JnLQmfTAjPxse7ElkG_2dfHZSl2JyCTfSBBw6OngQ Test results: Working on get it running, installed it >15 times with different versions or VM / physical and this file was all what was missing. It is ...

Recently, there are many customers who have reflected,the following tips appear when testing some Mercedes-Benz cars with V2018.09 MB STAR C4 SD Connect Compact Diagnosis tool: We first checked the hardware of MB STAR C4/C5 and found that the hardware works normally. The problem should be in the software section. One of the customers in Hong Kong reported that after the software upgrade to V2018.09, the Mercedes-Benz C-series car could not be connected, and the same prompt appeared above. Model of his car: Mercedes-Benz C320 chassis W204 2015. We looked at the diagnostic interface provided by the customer and found that there is a hardware icon for MB STAR C6 in the upper right corner of the xentry software interface, as follows: It turns out that the customer has set the hardware mode error to C6 mode. When the customer uses the Mercedes-Benz diagnostic tool MB STAR C4 or C5, the corresponding hardware mode must be set to C4 in the software. Your MB STAR...

If ICOM A2 clone with WiFi now I have seen that the most difference between an original BMW ICOM A2 and a clone is that the original has wifi capability, whereas the clone does not. Today the Eobd2 customer services tell me that their BMW ICOM A2+b+c diagnostic & programming tool now has wifi capability. And I saw a lot of people comment ICOM A2 clones with wifi capability that work reliably. On the more technical side, I’ve encountered through the grape vine that the new units that they add as a wifi Module is, “a Sparklan WMIA-199N based on an ATHEROS MIMO chip.” Apparently it is possible to, “get a fully functional Mini PCI port between the layers”(of the ICOM A2’s internal circuit boards that would allow for incorporating a wifi mod). You can get some information of BMW ICOM A2+B+C below: BMW ICOM A2+B+C Functions: A2 – OBD diagnostic supporting MOST, D-CAN and K-CAN protocols B – Diagnostic via most bus, and have connection to A-interface via USB connect...

How to Restore BMW diagnostic tool BMW ICOM Next? This post will show an obd2eshop customer’s solution to BMW ICOM Next restore when you has red LEDs turn on issue when running firmware upgrade. In order to solve your incident, please apply the following 12 steps: Note: DO NOT UNPLUG the BMW ICOM Next emulator from the {OBD II} jack after an update via {ISTA}, a web interface or an emergency software update. The {ICOM Next} starts with flashing green SYSTEM {LED}s. After about 10 seconds it shows red {LED}s for about 2 minutes. After this, the {ICOM Next} reboots due to a firmware update. If the {ICOM Next} {LED}s remain red for more than 10 minutes, or if the {ICOM Next} is unplugged directly after an update, please carry out the following procedure: 1. Please ensure that ALL of the following prerequisites are satisfied: 1.1. You require a USB 2.0 or USB 3.0 flash drive. {USB 1.x flash drives are not supported). 1.2. The USB flash drive must be formatted w...

How to Restore BMW ICOM Next ? This post will show an obd2eshop customer’s solution to BMW ICOM Next restore when you has red LEDs turn on issue when running firmware upgrade. In order to solve your incident, please apply the following 12 steps: Note: DO NOT UNPLUG the BMW ICOM Next emulator from the {OBD II} jack after an update via {ISTA}, a web interface or an emergency software update. The {ICOM Next} starts with flashing green SYSTEM {LED}s. After about 10 seconds it shows red {LED}s for about 2 minutes. After this, the {ICOM Next} reboots due to a firmware update. If the {ICOM Next} {LED}s remain red for more than 10 minutes, or if the {ICOM Next} is unplugged directly after an update, please carry out the following procedure: 1. Please ensure that ALL of the following prerequisites are satisfied: 1.1. You require a USB 2.0 or USB 3.0 flash drive. {USB 1.x flash drives are not supported). 1.2. The USB flash drive must be formatted with a FAT32 file...

Aftre the BMW ICOM host is connected to the car via a 16PIN connector, and the other side is connected to the computer via a network cable. Your OBD2 Scanner BMW ICOM lan and system lights will light up. As follows: But at this moment,the host can’t be found in the computer.As follows: When meeting the problem,please update your 30% Discount Products BMW ICOM firmware as the following method: 1.Please connect BMW ICOM to the computer vith network cable and power on the BMW ICOM with a 12V power adapter. 2.Open the website address http://169.254.92.38:60080/by IE browser, username:root   password:NZY11502. 3.Click the “update firmware”，it will show ICOM firmware version information. 4.Choose the file ICOM-BootImage-01-11-01.bin,set image type to SYSTEM，click “Send the file”. 5.When shows “Write the image file to the flash?”，click “Yes”,then ICOM light turns red. 6.When shows “The SYSTEM IMAGE update was successfull”，click “Update Firmware”. 7.Choose the fi...